diff --git a/common/Kconfig b/common/Kconfig
index ca136b1..82cd864 100644
--- a/common/Kconfig
+++ b/common/Kconfig
@@ -738,15 +738,17 @@
 
 if BLOBLIST
 
-config BLOBLIST_SIZE
-	hex "Size of bloblist"
-	depends on BLOBLIST
-	default 0x400
+choice
+	prompt "Bloblist location"
 	help
-	  Sets the size of the bloblist in bytes. This must include all
-	  overhead (alignment, bloblist header, record header). The bloblist
-	  is set up in the first part of U-Boot to run (TPL, SPL or U-Boot
-	  proper), and this sane bloblist is used for subsequent phases.
+	  Select the location of the bloblist, via various means.
+
+config BLOBLIST_FIXED
+	bool "Place bloblist at a fixed address in memory"
+	help
+	  Select this to used a fixed memory address for the bloblist. If the
+	  bloblist exists at this address from a previous phase, it used as is.
+	  If not it is created at this address in U-Boot.
 
 config BLOBLIST_ALLOC
 	bool "Allocate bloblist"
@@ -755,18 +757,31 @@
 	  specify a fixed address on systems where this is unknown or can
 	  change at runtime.
 
+endchoice
+
 config BLOBLIST_ADDR
 	hex "Address of bloblist"
 	default 0xc000 if SANDBOX
+	depends on BLOBLIST_FIXED
 	help
 	  Sets the address of the bloblist, set up by the first part of U-Boot
 	  which runs. Subsequent U-Boot phases typically use the same address.
 
 	  This is not used if BLOBLIST_ALLOC is selected.
 
+config BLOBLIST_SIZE
+	hex "Size of bloblist"
+	default 0x400
+	help
+	  Sets the size of the bloblist in bytes. This must include all
+	  overhead (alignment, bloblist header, record header). The bloblist
+	  is set up in the first part of U-Boot to run (TPL, SPL or U-Boot
+	  proper), and this sane bloblist is used for subsequent phases.
+
 config BLOBLIST_SIZE_RELOC
 	hex "Size of bloblist after relocation"
-	default BLOBLIST_SIZE
+	default BLOBLIST_SIZE if BLOBLIST_FIXED || BLOBLIST_ALLOC
+	default 0 if BLOBLIST_PASSAGE
 	help
 	  Sets the size of the bloblist in bytes after relocation. Since U-Boot
 	  has a lot more memory available then, it is possible to use a larger
@@ -775,6 +790,64 @@
 
 endif # BLOBLIST
 
+if SPL_BLOBLIST
+
+choice
+	prompt "Bloblist location in SPL"
+	help
+	  Select the location of the bloblist, via various means. Typically
+	  you should use the same value for SPL as for U-Boot, since they need
+	  to look in the same place. But if BLOBLIST_ALLOC is used, then a
+	  fresh bloblist will be created each time, since there is no shared
+	  address (between phases) for the bloblist.
+
+config SPL_BLOBLIST_FIXED
+	bool "Place bloblist at a fixed address in memory"
+	help
+	  Select this to used a fixed memory address for the bloblist. If the
+	  bloblist exists at this address from a previous phase, it used as is.
+	  If not it is created at this address in SPL.
+
+config SPL_BLOBLIST_ALLOC
+	bool "Allocate bloblist"
+	help
+	  Allocate the bloblist using malloc(). This avoids the need to
+	  specify a fixed address on systems where this is unknown or can
+	  change at runtime.
+
+endchoice
+
+endif # SPL_BLOBLIST
+
+if TPL_BLOBLIST
+
+choice
+	prompt "Bloblist location in TPL"
+	help
+	  Select the location of the bloblist, via various means. Typically
+	  you should use the same value for SPL as for U-Boot, since they need
+	  to look in the same place. But if BLOBLIST_ALLOC is used, then a
+	  fresh bloblist will be created each time, since there is no shared
+	  address (between phases) for the bloblist.
+
+config TPL_BLOBLIST_FIXED
+	bool "Place bloblist at a fixed address in memory"
+	help
+	  Select this to used a fixed memory address for the bloblist. If the
+	  bloblist exists at this address from a previous phase, it used as is.
+	  If not it is created at this address in TPL.
+
+config TPL_BLOBLIST_ALLOC
+	bool "Allocate bloblist"
+	help
+	  Allocate the bloblist using malloc(). This avoids the need to
+	  specify a fixed address on systems where this is unknown or can
+	  change at runtime.
+
+endchoice
+
+endif # TPL_BLOBLIST
+
 endmenu
 
 source "common/spl/Kconfig"